Chevrolet CAMARO 2011 Manual de servicio

Turbonetics, Inc. * 14399 Princeton Avenue * Moorpark, CA * 805-581-0333 * TurboneticsInc.com www.Turboneticsinc.com INSTALLATION INSTRUCTIONS TUR

60203_revB Page 10 of 35 11. Disconnect the AC pressure sensor harness. Remove the sensor and O-ring. The shrader valve inside the AC line will pr

60203_revB Page 11 of 35 TURBO WATER LINE INSTALLATION 1. Locate the two heater hoses where they attach to the thermostat housing on the passenger

60203_revB Page 12 of 35 7. Install 12” of heat shielding over the oil drain hose and secure with zip ties. BATTERY CABLE / OIL FEED LINE IN

60203_revB Page 13 of 35 7. Install and tighten the -4 oil line (with heat shielding) to the fitting as shown, leaving the other end disconnected.

60203_revB Page 14 of 35 2. Loosen the two nuts on each of the exhaust clamps connecting the cats to the cat back exhaust and slide passenger side

60203_revB Page 15 of 35 TURBOCHARGER INSTALLATION 1. Loosely attach the cat to turbo #3 bracket (22141) to the cat to turbo #3 pipe (22127) flang

60203_revB Page 16 of 35 5. Attach cat to turbo #2 bracket (22139) to the boss on the engine block behind the exhaust manifold with the suppli

60203_revB Page 17 of 35 9. Connect the oil drain line to the fitting previously installed in the oil pan and secure with a pinch clamp. 10. Using

60203_revB Page 18 of 35 5. Remove the two bolts from the rear of the A/C compressor. Install the supplied turbo downpipe 2-3 bracket (22142) and

60203_revB Page 19 of 35 7. Install the turbo downpipe #2 pipe (22129) into the space between the A/C compressor and the frame. The flared end sho

60203_revB Page 2 of 35 Read This First Study these instructions completely before proceeding. Engine and/or turbocharger damage may occur if any c

60203_revB Page 20 of 35 10. Install the supplied heat shield onto the turbine housing and secure with safety wire looped around the three metal ho

60203_revB Page 21 of 35 16. Tighten the clamps just enough to be snug but still allow a little movement for alignment later WASTE GATE INSTAL

60203_revB Page 22 of 35 4. Attach and tighten the base of the waste gates to the cat to turbo #1 pipe flanges using M8 nuts and lock washers. 5.

60203_revB Page 23 of 35 11. Pre-install 2 ½” clamps onto the turbo exhaust. Slide the tail pipes through the rear valance. Line up the

60203_revB Page 24 of 35 2. Install the upper radiator tube with two 1 3/8” couplers and #24 hose clamps. Connect the open end of the previously i

60203_revB Page 25 of 35 7. Remove the windshield washer pump from the factory reservoir. Use the supplied loop clamp and 1/4” bolt to secure

60203_revB Page 26 of 35 2. Thread the supplied 1/8” npt to 5/32 hose fitting into the hole in the bottom of the intercooler. Thread a vibration d

60203_revB Page 27 of 35 6. Mount the intercooler to the bottom of the core support as shown using large flat washers and the two M8 lock nuts. Co

60203_revB Page 28 of 35 3. Remove the Mass Air Flow (MAF) sensor from the factory air box lid. 4. Install the MAF into the supplied intercooler

60203_revB Page 29 of 35 2. Do not remove the white pad from the air filter housing. Place the factory air filter onto the housing and secure by s

60203_revB Page 3 of 35 #15192 CAMARO TURBOCHARGER SYSTEM PARTS LIST: QTY P/N DESCRIPTION TURBO KIT# 15192 (COMPONENTS) 2 11570 Wastega

60203_revB Page 30 of 35 7. Clean the plastic, apply a small amount of sealant to the check valve and press it into the intake manifold. Remo

60203_revB Page 31 of 35 10. Remove the vacuum hose from the brake booster reservoir. Using sealant, install the 1/16 npt to 3/16” barb fitt

60203_revB Page 32 of 35 2. Check that all hose routings are free of any kinks or near any hot or abrasive surfaces that may cause wear over time.

60203_revB Page 33 of 35 ECU REPROGRAMMING 1. Plug the included Diablosport up loader into the OBDII port located underneath the driver’s side dash

60203_revB Page 34 of 35 4. Follow instructions and after the original backup has been saved, select “Install Tune”*. Follow the instructions unti

60203_revB Page 35 of 35 “NO FAULT / NO HASSLE” WARRANTY PROGRAM: TURBONETICS will repair or replace, at our expense, any new TURBONETICS / Spearco

60203_revB Page 4 of 35 #15194 CAMARO TUNER KIT QTY P/N DESCRIPTION TUNER KIT# 15194 (COMPONENTS) 2 10781 Wastegate Ass'y, 9 Psi

60203_revB Page 5 of 35 P/N 11570 P/N 11491 P/N 11558 P/N 11559 P/N 11560 P/N 11561 P/N 11562 P/N 11571 P/N 31360 P/N 11545-BB P/N 70063

60203_revB Page 6 of 35 P/N 22134 P/N 22135 P/N 22125 P/N 22126 P/N 22127 P/N 22128 P/N 22129 P/N 22130 P/N 22131 P/N 22145 P/N 22144 P/

60203_revB Page 7 of 35 P/N 22139 P/N 22140 P/N 22141 P/N 22142 P/N 22143 P/N 11566 P/N 22034 P/N 22122 P/N 22123 P/N 22121 P/N 22132 P/N

60203_revB Page 8 of 35 PREPARING THE VEHICLE FOR TURBO KIT INSTALLTION 1. Jack the vehicle up to a workable height. Secure the vehicle with jack

60203_revB Page 9 of 35 7. Remove 6 bolts securing the metal bumper (3 each side). 8. Remove 6 plastic clips and ambient air temp sensor fro